Hackintosh ZONE - AMD build - Unable to boot in normal mode - Hackintosh Yosemite - Hackintosh Zone Hackintosh ZONE - AMD build - Unable to boot in normal mode Jump to content
lordmeka

Hackintosh ZONE - AMD build - Unable to boot in normal mode

Recommended Posts

Hi Guys, I would like your help on my Hackintosh system. I can start in safe mode without any problem just by using ( -x npci=0x2000 ). The problem is that I cannot start in normal mode. It hangs on a gray screen with the spinning lollipop/wheel and just sits there not doing anything. I used only hackintosh zone distro and did not install anything else except the network Kext with KextBeast. 

My build is:

MOBO: Gigabyte GA 990FXA-UD3 Rev 3.0

CPU: AMD FX 8350 Black Edition

GPU: MSI AMD ATI HD 7750 (Cape Verde) 1Gb VRAM DDR5

RAM: 8Gb Corsair Vengeance Black DDR3

Network: Realtek chipset RTL 1869 (from TPLink on PCI) - managed to get it run on my first try with KextBeast with native support after removing ATI kexts

Distro: Hackintosh Zone Yosemite 10.10.1

 

My problem is I am new to this :) 

I am stuck at this point in safe mode and I don't know where to go from here.

What I tried until now:

Booting in normal mode with the following flags:

1.) npci=0x2000 GraphicsEnabler=Yes PCIRootUID=1 -v   -> Not working

2.) npci=0x2000 GraphicsEnabler=No -v                             -> Not working

===================================================

PS: I am unable to boot otherwise, I have no secondary on board card. I would appreciate all suggestions with detailed explanations because I have no clue how to do a DSDT injection or more complicated stuff, but if it's explained step by step I can get it.

On my first try I managed to enter in safe mode only through HDMI with my Samsung TV connected because it had dual display set up default and I used PCIRootUID=1 on the second install and now I don't need the HDMI to see my screen on my BENQ monitor.

Thank you in advance.

Edited by lordmeka

Share this post


Link to post
Share on other sites

Hi Guys, I would like your help on my Hackintosh system. I can start in safe mode without any problem just by using ( -x npci=0x2000 ). The problem is that I cannot start in normal mode. It hangs on a gray screen with the spinning lollipop/wheel and just sits there not doing anything. I used only hackintosh zone distro and did not install anything else except the network Kext with KextBeast. 

My build is:

MOBO: Gigabyte GA 990FXA-UD3 Rev 3.0

CPU: AMD FX 8350 Black Edition

GPU: MSI AMD ATI HD 7750 (Cape Verde) 1Gb VRAM DDR5

RAM: 8Gb Corsair Vengeance Black DDR3

Network: Realtek chipset RTL 1869 (from TPLink on PCI) - managed to get it run on my first try with KextBeast with native support after removing ATI kexts

Distro: Hackintosh Zone Yosemite 10.10.1

 

My problem is I am new to this :) 

I am stuck at this point in safe mode and I don't know where to go from here.

What I tried until now:

Booting in normal mode with the following flags:

1.) npci=0x2000 GraphicsEnabler=Yes PCIRootUID=1 -v   -> Not working

2.) npci=0x2000 GraphicsEnabler=No -v                             -> Not working

===================================================

PS: I am unable to boot otherwise, I have no secondary on board card. I would appreciate all suggestions with detailed explanations because I have no clue how to do a DSDT injection or more complicated stuff, but if it's explained step by step I can get it.

On my first try I managed to enter in safe mode only through HDMI with my Samsung TV connected because it had dual display set up default and I used PCIRootUID=1 on the second install and now I don't need the HDMI to see my screen on my BENQ monitor.

Thank you in advance.

Try vga or dvi and make sure u backup all graphics kext to do that u should boot with -s and wait till its says root and type 



fsck -fy 

mount -uw/

grafix backup all 

reboot 



after those steps try to boot with /amd64

Hope i helped

I also have a amd system

  • Like 1

Share this post


Link to post
Share on other sites

Try vga or dvi and make sure u backup all graphics kext to do that u should boot with -s and wait till its says root and type 


fsck -fy 

mount -uw/

grafix backup all 

reboot 



after those steps try to boot with /amd64

Hope i helped

I also have a amd system

I tried now booting in single user mode to repair my HSF partition but I can't, this FS is kind of easy to break I see. Can I use fsck to fix the file system?

Diskutil says I can't repair my partition. Is there any chance to repair it? Or I have to reinstall the whole system again?

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Donation Goals

    Hosting July 2018

    Please donate to support the community.
    We appreciate all donations!

    Thanks



    $17.91 of $100.00 goal reached.
    Donate Now
  • Download Hackintosh

  • Posts

    • Hey guys, this is my first post on this forum.   I've installed High Sierra on my box.   These are my settings:   Intel Core i5 3570k (Intel HD 4000) MSI Z77A-G41 8GB RAM 120GB SSD + 1TB HDD   I'm using an HDMI cable with a monitor resolution 1920x1080   Everything is working fine... I've got my LAN working after installing some kexts.   But now I can't have my VGA working properly (some glitches and slowdowns).   I've tried alot of things that I've found on the internet, like changing config.plist on Clover with some different settings. But nothing worked for me... even youtube videos showing how to get it to work...   Can you guys help me please?   Thanks!
    • 1--> https://photos.google.com/photo/AF1QipM62-Ht1JeeKXUn6BS-HM-cD4zgo3FxRpj8oOpD   2-->https://photos.google.com/photo/AF1QipNpz7cJKAi4ppNC3HAMlhL1ZfdCGmxyq-MgmNw5 system configuration link-->  1-->https://photos.google.com/photo/AF1QipMk1174nfxqu3HEBS004g-644jFbWhkRspjllDb 2-->https://photos.google.com/photo/AF1QipMcZd0YSTq2VNbzzI4zplay-S2fqT2NThWKPJ6g   Please help me to install hackintosh on my laptop   Thanks   
    • Hi You might use Apple Disk Utility to clone the disk. May be you must  write a disk image of your Startup disk first. Carbon CopyCloner will do it too ( EVEN IF THE DISK IS IN USE). Then you must install Clover on the Disk and copy the contents of the efi Partition of your startup dist to the Clone. Voila thats it.
    • I have an HP desktop that is running Niresh Mavericks. I have a second computer that is identical. I haven't been able to get the distro to install. Is there a way to copy the boot drive that works now and put that copied drive into the second machine. The second machine allows me to install the Niresh distro, but then won't boot from it at all. Can I use an Ultimate Boot CD to clone the drive?  Also, I check both computers and they are both running the exact same bios and settings.  
  • Download Statistics

    • Files
      850
    • Comments
      2,144
    • Reviews
      2,586

    Latest File
    By Niresh

    951    0

×