Jump to content
pepe999

10.14.4 update

Recommended Posts

pepe999

Hi guys,

Has anyone upgraded to the latest version? I was able to install a command line update but the 14.4 installer gets stuck after a minute. Thx

Share this post


Link to post
Share on other sites
Hackintosh

@pepe999

I was able to upgrade. It was just simple upgrade.

Where was it stuck?

Any Kernel Panic?

Share this post


Link to post
Share on other sites
pepe999

Unfortunately I don't have Clover set to verbose so once I select the installer it goes straight into the usual blank boot screen with the progress bar and stops in a minute with like a 5% done. Today I tried it with laptop off the power cord and the progress bar got stuck at 65%. 

Share this post


Link to post
Share on other sites
Hackintosh

@pepe999 If you have another macOS Volumes, You can try to Install package with Terminal to your Main OS.

Share this post


Link to post
Share on other sites
pepe999

I prefer a command line over the GUI package manager on linux. Got Mojave installed on the full drive so no other Mac volumes. Never had any issue with updates before on HS or Mojave. 

Share this post


Link to post
Share on other sites
pepe999

A bit progress now. After like 15 minutes of idle state the installer started working again but ended soon after with a blank black screen. Seems like it doesn't like my graphics Intel HD 4600 or the 1600x900 resolution. 

Share this post


Link to post
Share on other sites
pepe999

It's done now. After a reboot it got stuck again for another 15 minutes. After that a blank screen came up for 5 minutes which was followed by the installation wizard that finished the installation. I have never seen an update like that before on Win or linux. 

Share this post


Link to post
Share on other sites
Hackintosh

@pepe999 Does it work now?

Share this post


Link to post
Share on other sites
pepe999
23 hours ago, Niresh said:

@pepe999 Does it work now?

Yes, all fine. The previous updates took a bit long with 5 to 6 reboots but this one was really scary because the updates never froze. Got a 16GB RAM, SSD and proper 3GHz Haswell mobile processor not the ultra voltage version. 

  • Like 1

Share this post


Link to post
Share on other sites
blast9999
On 3/28/2019 at 7:18 AM, pepe999 said:

It's done now. After a reboot it got stuck again for another 15 minutes. After that a blank screen came up for 5 minutes which was followed by the installation wizard that finished the installation. I have never seen an update like that before on Win or linux. 

I've had that long delay a couple times including original install of Niresh Mojave on my gigabyte H87N-WIFI. This time it took forever. I tried all the boot options before it finally worked. 

To be clear, which is the correct boot option after the updater adds them?

Share this post


Link to post
Share on other sites
pepe999

I used to have only one which was the main OS called Mojave. Once an update was available then Install Mojave option appeared. It was selected by the system after each reboot while updating and after the progress bar was about 80% it rebooted for the last time and disappeared with the Mojave boot the only option when the update was finished. You have to ask Niresh which of the preboot options should be selected for an update. I had 4 different options on High Sierra and remember that I had to change the boot option manually because the update would start all over again if I kept the same option. 

Share this post


Link to post
Share on other sites
pepe999

Hmm, I have got a Haswell laptop and that Gigabyte H87N board is a desktop Haswell. I hope that Apple are not dropping Haswell support. 

Share this post


Link to post
Share on other sites
Dipendra

Hi,

 

Currently I have MacoS Niresh mojave 10.14.1 now to I want to update 10.14.4 .

 

Please share the steps .

 

 

Regards,

Dipendra

Share this post


Link to post
Share on other sites
blast9999
20 hours ago, Dipendra said:

Hi,

 

Currently I have MacoS Niresh mojave 10.14.1 now to I want to update 10.14.4 .

 

Please share the steps .

 

 

Regards,

Dipendra

You can update with System Prefs> Software Update just like a real Mac : )

  • Like 1

Share this post


Link to post
Share on other sites
dmitrij999
On 4/6/2019 at 6:17 AM, blast9999 said:

You can update with System Prefs> Software Update just like a real Mac : )

but it suggests update only to Catalina. I tried to install Catalina on my laptop with i3-3110M processor, but it tried to reboot... and froze

Share this post


Link to post
Share on other sites
blast9999

Yeah only incremental software updates work on a Hackintosh.

Share this post


Link to post
Share on other sites
dmitrij999
On 12/8/2019 at 12:41 AM, blast9999 said:

Yeah only incremental software updates work on a Hackintosh.

does it help if I try to install update from clear dmg image?

Share this post


Link to post
Share on other sites
blast9999

No. You need to do a fresh install using an installer stick. 

Share this post


Link to post
Share on other sites
dmitrij999
18 minutes ago, blast9999 said:

No. You need to do a fresh install using an installer stick. 

but Niresh Mojave version is 10.14.1 available for download

Share this post


Link to post
Share on other sites
blast9999

That’s because he created the installer when 10.14.1 was the current available MacOS. 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...