Jump to content
Devonic

How to Fix Mavericks not booting after the 10.9.2 Update

Recommended Posts

DISCLAIMER : The 10.9.2 update has broken a lot of installations of Niresh's Mavericks distro due to a new version of Darwin. The steps described below are a generic solution as discussed on various parts of the forums. This is just a re-organized and structured version of the fix. This may not necessarily work for all OSX installs. So instead of only using the kexts packaged by Niresh, please backup any custom kernels or even better your entire extensions folder.

 

Stuff you need :

1) A 1 GB USB (any size actually)
2) The Niresh Mavericks Installer USB
3) An already working mavericks install (optional)


If you are stuck with a non-booting Installation of OSX Mavericks :
1) Head over to Windows and download Transmac.
2) Download the PCI Config Kexts from here.
3) Plug in your 1 GB USB and format it to Mac OSX Extended Journaled by right clicking and selecting "Format Disk for Mac"
4) Make a folder named Extensions in the root directory of the USB in Transmac (+HFS Volumes > Right click on White Space > Make New Folder)
5) Copy the kexts (not the folder, the kexts ! ) you downloaded into the Extensions folder.
6) Rename your 1 GB USB to FIX. (If you can't do this using Transmac, format the USB using the Niresh Installer and rename to
FIX. Then proceed with Transmac steps (without       formatting of course)
You're done for the windows part !

Now boot into the Niresh Mavericks Installer

1) Plug in your 1 GB USB after the Welcome Screen has appeared
2) Go to disk utility and mount your FIX usb (Right Click the USB > Mount)
3) Open Terminal and type the following :

ditto -V /Volumes/FIX/Extensions/*there is a single space here*/Volumes/*THE NAME OF YOUR HARD DRIVE*/System/Library/Extensions/
chown -R root:wheel /Volumes/*THE NAME OF YOUR HARD DRIVE*/System/Library/Extensions/
chmod -R 755 /Volumes/*THE NAME OF YOUR HARD DRIVE*/System/Library/Extensions/

2) Exit out of Terminal and Reboot
3) Your Hackintosh should finally boot into OSX 10.9.2  :)

If you have a Working Mavericks Installation before hand:

1) Just copy the PCI Fix kexts into a USB Formatted using Disk Utility into Mac OSX Extended Journaled and repeat the same steps from step number 6.

2) Additionally backup the Extensions folder and your Kernels to the USB with a different directory name.

Cheers  :D

 

Edited by Devonic
addtional steps.
  • Like 3

Share this post


Link to post
Share on other sites

doesn't work for me =/

Share this post


Link to post
Share on other sites

@FightClub which part doesn't work for you ?

Share this post


Link to post
Share on other sites

I went exactly as it was described but it just laughed at me restarted then taunted me some more. I'm just going to wait for NERESH to update to 9.2. I have more concerns then getting 9.2 installed. Like the Nvidia kext installed. HDMI works flawlessly but my main display never works when I switch to the Nvidia from Apple. I restart with HDMI support and no main Display support. I have a 3D Display so I think I'm just fawked.

Share this post


Link to post
Share on other sites

Hi everybody and sory if my english is not so good.

I have successfully updated from 10.9.0 to 10.9.2 and fully functional with this configuration:

 

AMD Phenom II x4 925

Gigabyte ma770t-ud3

8GB 1600 DDR3

Gainward GT240

sata WD 320G with windows 8 installed

sata WD 1T with Mavericks

 

I backed up only 3 kexts from 10.9.0 : System.kext, AppleMatch.kext, Sandbox.kext from System/Library/Extensions

and put them together with "match_kernel" in one folder on desktop, after that i installed combo update 10.9.2 and rebooted into windows 8. With program "mac drive" from windows i go to mac partition and put this 3 kext that i backed up on desktop in 

System/Library/Extensions with replacing files, and mach_kernel in root of drive alsou with replacing file. I rebooted again but this time from my USB flash with Nireshs Mavericks installation, started disk utility and repaired permissions for mac drive.

Reboot again this time from mac partition and with flags -x -v. When i get to desktop just run kext wizard to repair permissions and after that rebooted normal in 10.9.2 with everything working perfectly

Kernel "AMD 10.9/10.9.1/10.9.2 kernel, with SSE3 and opemu Version R6" was not so good for my spec, i had some glitches so i used this kernel that works perfectly for me:    http://speedy.sh/fyQ3k/mach-kernel

 

Hope this help somebody

  • Like 1

Share this post


Link to post
Share on other sites

@FightClub If you have the option to set your 3D-Display form 120 Hz to 60Hz, it might work.

Share this post


Link to post
Share on other sites

The option doesn't come up with my main display. It being connected to my HDTV though 3D scales down to 60Hz. My laptop display doesn't show up with Nvidia kext active. With Apple display active. It doesn't show any refresh rate at all, just that I set it at a HD resolution. Wish it were that simple.. I may just need to get another display.. thanks Devonic for trying to help me out. not many people would go out there way to. witch in my book makes you awesome! Its a up-hill battle I'll eventually figure out..

Share this post


Link to post
Share on other sites

Hello grujev. you have a AMD, I have a Intel, I don't think that mach-kernel would work for my system. Thanks anyways bro :)

Share this post


Link to post
Share on other sites

Dont work for me this Fix.  Try too grujev fix and the computer enter in boot crash and boot again.

 

AMD FX here.

Share this post


Link to post
Share on other sites

@Devonic Thanks for this.

 

Can you please explain what the purpose of this is: https://www.hackintoshzone.com/files/file/94-amd-10910911092-kernel-with-sse3-and-opemu/ ?

 

Also there is this one which was uploaded more recently, but does not say it supports 10.9.2: https://www.hackintoshzone.com/files/file/148-amd-kernel-for-os-x/

 

Do you think I should install these kernels before proceeding with the 10.9.1 -> 10.9.2 update? I use AMD FX-8320. Thank you.

 

edit: OK, I just noticed what grujev posted about the kernels. They said the first one that I linked to was buggy for them. The other one I linked to is newer, but much smaller file size than "mach kernel" that was posted by grujev.

 

I just found an AMD kernel for "10.9.*" on another site uploaded as recent as March 9th, 2014 --- but explicitly says in the file description not to update to 10.9.2  :o

Share this post


Link to post
Share on other sites

@iLL It's pretty self explanatory, it's an AMD Kernel (there are many variations floating around). The basic core instruction of the guide is Backup your kexts, backup your custom kernels and restore using the installer terminal. Since many did not know the terminal commands, i just made a guide. 

Yes install and backup the kernels and update.

I don't exactly advocate the update as many users have problem since Darwin is updated, but if you want to take a plunge go for it.

  • Like 1

Share this post


Link to post
Share on other sites

@iLL

I don't exactly advocate the update as many users have problem since Darwin is updated, but if you want to take a plunge go for it.

 

Yeah, as much as I would like to run the latest version, I might just wait it out and see how the progress comes with the 10.9.2 compatible kernels. For now, Mavericks 10.9.1 is working pretty stable for me on AMD FX-8320 using Radeon HD 7970 with the kernel that was included with the Niresh Mavericks USB image. Thank you. Much respect to Niresh as well for making this so easy.

Share this post


Link to post
Share on other sites

@iLL Yeah, OSX 10.9.2, besides the massive SSL fix is not much to get excited for. Do not rest ! Keep experimenting with Vanilla installs of OSX as you'll get a better idea of what patches you apply and where which Niresh's distro makes overwhelmingly transparent and easy. 

Share this post


Link to post
Share on other sites

I'm stuck on "GeforceSensors: still waiting for accelerator to start"

AMD phenom II x4

Gtx 470

16GB RAM

250GB HDD

10.9 Runs Perfect without iCloud -.- thats the reason why i tried to update.

Any ideas ?

Share this post


Link to post
Share on other sites

I'm stuck on "GeforceSensors: still waiting for accelerator to start"

 

Found this info on google:

 

 

However, updating to the retina 10.9.1 version caused the laptop to reboot just before getting to the desktop (with a message about GeforceSensors: Waiting for accelerator to start).

 

Edit: the problem is Geforce related, removing the NVDRESMAN kexts allos me to go to desktop with the IntelHD 4600 (wih full acceleration).

 

I think if you insert and boot from Niresh installation CD/USB, you'll have the option to use the -x boot flag to disable graphic kexts, which should get you to the point where you can remove the problematic kext... but I don't really know, so maybe it would be better to wait for someone else to help.

Share this post


Link to post
Share on other sites

Hello my problem is i have to write cpus=1 when start up but the laptop is not as fast as before , 

i have an hp g6 1288sl 

Thanks.

 

i was wondering how to patch the hp file again ??

Share this post


Link to post
Share on other sites

Hello I have a problem when I type the command in terminal it says

ditto -V /Volumes/FIX/Extensions/ : file or directory doesn't exist please help

Share this post


Link to post
Share on other sites

@ Did you rename the usb to FIX ?

Share this post


Link to post
Share on other sites

@Devonic I did I tried changing the USB too it still says : ditto-V/ Volumes /FIX/ Extensions: no such file or derictory I did all the steps again but still says the same thing

Share this post


Link to post
Share on other sites

@ Make sure you go to Disk Utility and mount your USB named FIX (right click FIX > Mount)

Share this post


Link to post
Share on other sites

@Devonic i tried that

I was wondering can I mount my hard drive in another mavericks and try the commands in terminal ?

Share this post


Link to post
Share on other sites

123.png

 

How i change the name if i cant see that option!?

how i open the terminal?

Is the rest ok? (extensions folder and the other folders)

Share this post


Link to post
Share on other sites

@ You can actually mount it inside the Niresh Installer Setup in Disk Utility and Format it to the name FIX and then proceed with the steps in transmac.

Open Terminal after you have booted into the Niresh Installer. Utilities > Terminal (on the status bar )

Share this post


Link to post
Share on other sites

Followed The Instructions And It Worked Great, Thanks :)

  • Like 1

Share this post


Link to post
Share on other sites

Followed the instruction but still stuck in bootloop, no way out :-(

 

My computer specs

 

Gigabyte 970A-DP3

FX8320

Ram Cosair 16GB 1600MHz 9-9-9

PSU Cosair CX 500W

2 Seagates 500GB HDD

1 WD 1TB HDD

Share this post


Link to post
Share on other sites

And now?

 

ditto -V /Volumes/FIX/Extensions/ /Volumes/Integral Courier Media/System/Library/Extensions/

ditto: can't get real path of source

 

20140404_224439_1.jpg

Share this post


Link to post
Share on other sites

@

I'm pretty sure the correct syntax would be :

ditto -V /Volumes/FIX/Extensions/ /Volumes/MAC/System/Library/Extensions/
  • Like 1

Share this post


Link to post
Share on other sites

Hi Everyone,

 

First I'll post my PC's specs and then go into how I was able to get 10.9.2 to boot after I updated from Niresh's 10.9.0.

 

PC Specs:

AMD FX-6200 3.8 GHz 6 core cpu

Gigabyte GA-890GPA-UD3H Motherboard

8GB Kingston HyperX 1600 MHz memory

EVGA GeForce GTX 260

700W OCZ ModXstream Pro PSU

 

So I am currently just using a couple of old SATA 2 80GB WD hard drives. One was for my initial installation, the other is being used as a clone and the drive I do all of my testing on.

So the first thing I did was make the installer and boot from it. On initial boot, I only needed to use one boot flag which was "amdfx" (without quotes of course) and I used the optional but very helpful "-v" (verbose) flag to make sure there were no errors.

After setting up my drive I went to "customize" but didn't change much at all.

I enabled all but the ACPI sensor under the FameSMC plugins section. (HWMonitor shows all of my temps)

I enabled USBBusFix=Yes, UHCIreset=Yes and EHCIacquire=Yes.

The installer already used npci=0x2000 and GraphicsEnabler=Yes so I had nothing to add there for my graphics card.

 

After the mavericks installed, it rebooted and went right into my desktop with full qe/ci enabled.

So now I cloned the drive, downloaded the 10.9.1 update from apple and the 10.9.2 combo update. I updated the clone to 10.9.1 and booted from it to make sure it would run alright. It did, so I booted back into the main drive and installed the 10.9.2 combo update onto the clone. (going to 10.9.1 first may be an uneeded step for your system, so if you want to go straight to 10.9.2, try it out!)

 

This is where the clone stops booting properly no matter what I do. I would get panics or other odd errors, everytime I booted. I downloaded the fix from this post, but unfortunately it did not work for my setup, so I continued my search for a fix and found a kernel that worked perfectly!

 

I hope I am allowed to post links to external sites here, because everyone struggling with getting 10.9.2 to boot properly with and AMD CPU needs to try this one out!

 

www.osx86.net/file/3736-amd-10910911092-kernel-update-iii-with-full-sse4-support/

 

The instructions say to copy System.kext, AppleMatch.kext & Sandbox.kext from 10.9.0 to System/Library/Extensions on your 10.9.2 drive and then repair permissions and restart your System

 

This file also has a support.kext file included, but I did not use this one. I used the one from my 10.9.0 drive which worked fine.

I used kext wizard to install the kexts, backup the 10.9.2 kexts and then after I backed up the current mach_kernel and copied over this modded kernel, repaired permissions and rebuilt the cache.

 

After all of that, I rebooted the clone and waited with my breath held like I was updating the BIOS on a motherboard! (If you've ever had a motherboard BIOS update go sideways, you will understand!)

 

I am happy to say that I am writing this reply in 10.9.2 on my AMD FX-6200 based PC!

 

I hope this will help everyone else out there that are struggling with this update!

 

  • Like 2

Share this post


Link to post
Share on other sites

Hi there
 
I successfully update OS X 10.9.0 to 10.9.2 (Niresh Distro)
 
PC Config Specifications
CPU: Intel Core i3 3,41 GHz
Motherboard: Asus P8Z77-V LX
Ram: 4GB Kingston 1333 MHz
GPU: EVGA Nvidia GeForce GT 610 2GB
Hard Disk: Seagate 2TB

 

Click on the link to see the proof

http://s2.postimg.org/l5lye3mmx/Schermata_2014_04_09_alle_14_08_58.png

 

Step by Step Guide:

1) Remove any trace of GPUSensors.kext from /System/Library/Extensions and repair permissions
2) Backup NullCPUPowerManagement.kext and remove it from /System/Library/Extensions
3) Download the patched mach_kernel for 10.9.2

4) Backup your graphics kexts by using the terminal because the combo update replace the patched kext with the native one:

a.       Create 'backup' folder

 mkdir /Volumes/ NameOfOSXDisk /backup

e.g.: mkdir /Volumes/MAVS/backup

b.      Select "Extensions" folder directory

 cd /Volumes/MAVS/System/Library/Extensions

c.         Transfer kexts to 'backup' folder

     cp AppleIntelHD* AppleIntelSNB* AMDRadeon* ATI* GeForce* NVDA* "/Volumes/MAVS/backup"

e.        Verify all kexts transferred:

 cd /Volumes/MAVS/backup

 ls

5) Copy the patched mach kernel, the graphics kext backup folder (which you find it in your OS X partition) and NullCPUPowerManagement.kext in a usb stick

6) Download OS X Mavericks 10.9.2 Update (Combo) and install it

 
Now there are two way to continue the upgrading process, you can use Windows or the terminal of the Niresh distro usb installation
 
7.1) If you have a Windows partition in your pc:
 
      a) First download Paragon for Windows, install it and reboot your pc

      B) Now you should see the OS X partition in My Computer

      c) Plug the usb stick where you have the copied files

      d) Now replace the mach_kernel in the Mac partition, then copy/replace NullCPUPowerManagement.kext and graphics kext in OS X Drive/System/Library/Extensions

      e) Now reboot to your OS X partition and Mavericks should be working

 

7.2) If you want use the terminal:

      a) Boot to the usb installer

      B) After the boot completed open the terminal plug and the usb where you copied the previous files

     c) Then follow the instructions:

a.       Verify secondary USB stick location:

     diskutil list

b.      Mount it:

     diskutil mount /dev/diskXsY

e.g.: diskutil mount /dev/disk2s1

Terminal will confirm the name of the disk mounted

c.       Select directory of USB stick's root:

     cd /Volumes/USBStick/

e.g.: cd /Volumes/CRUZER/

d.      Copy over patched mach_kernel [and NullCPUPowerManagement]

    cp /mach_kernel "/Volumes/NameOfOSXDisk/mach_kernel"

 e.g.: cp /mach_kernel "/Volumes/MAVS/mach_kernel"

    cp -R /Volumes/CRUZER/NullCPUPowerManagement.kext "/Volumes/MAVS/System/Library/Extensions"

                    e.      Copy the graphics kext

                             cd /Volumes/USBStick/backup

                             cp -R AppleIntelHD* AppleIntelSNB* AMDRadeon* ATI* GeForce* NVDA* "/Volumes/MAVS/System/Library/Extensions"

                    f.   Quit terminal and reboot to your OS X Partition

 

8) Now you should have Mavericks fully updated to 10.9.2. If you have some graphical issue or Audio issue or something else, use Multibeast or search on google the suitable kext for your requirements.

  • Like 2

Share this post


Link to post
Share on other sites
I hope I am allowed to post links to external sites here, because everyone struggling with getting 10.9.2 to boot properly with and AMD CPU needs to try this one out!

 

www.osx86.net/file/3736-amd-10910911092-kernel-update-iii-with-full-sse4-support/

 

The instructions say to copy System.kext, AppleMatch.kext & Sandbox.kext from 10.9.0 to System/Library/Extensions on your 10.9.2 drive and then repair permissions and restart your System

 

This file also has a support.kext file included, but I did not use this one. I used the one from my 10.9.0 drive which worked fine.

I used kext wizard to install the kexts, backup the 10.9.2 kexts and then after I backed up the current mach_kernel and copied over this modded kernel, repaired permissions and rebuilt the cache.

 

After all of that, I rebooted the clone and waited with my breath held like I was updating the BIOS on a motherboard! (If you've ever had a motherboard BIOS update go sideways, you will understand!)

 

I am happy to say that I am writing this reply in 10.9.2 on my AMD FX-6200 based PC!

 

I hope this will help everyone else out there that are struggling with this update!

 

 

 

AMD FX-8350 8-core

Asus Sabertooth 990FX R2.0 MB

20 GB Ram

MSI N560GTX-Ti GPU 1GB

1 TB WDC HDD SATA2 (Mavericks 10.9.2)

2TB Seagate HDD SATA2 (Windows 8.1 Pro)

Logitech Unified Keyboard/Mouse

 

I did exactly this, but I get severe performance issues From 10.9.2 that I did not have in 10.9.0. Every time I move the mouse it lags severely and clicks are delayed. Can barely use it. Upgraded Video Drivers from Nvidia Web Drivers and no difference. Also a thing from 10.9.0 Safari is unreadable because there are lines through everything. Looks like a printer running out of ink. No worries on that though, I use Firefox anyways. Much clearer. But it is "Working".

Share this post


Link to post
Share on other sites

Hi Everyone, I hope someone can help me out with my laptop configuration, I am very new with macs and hackintosh but I successfully installed the niresh version of mavericks 10.9.0 but with some issues my laptop configurations is:

 

Acer V5 571PG-9814

Intel I7 2.49mhz

Graphics: Intel HD4000 and Nvidia 710M 1GB

Bluetooth atheros

Wifi Atheros

Ethernet Realtek

Synapthics touch pad

 

after installations completes I have this result:

Graphics: intel hd4000 64mb shared full resolution but with flickers when open safari, cannot see videos because shows black video just sound

Bluetooth button shadow cannot turn off or on and just works if the pc is not turn off for so long after that recognized but doing nothing

Wifi not detected

Ethernet ok

touchpad ok installed synaptics kext, my screen is touchscreen with elantouch windows driver but not working for me in mac

SD Card Reader not recognized

 

I just learned a little bit about kext nothing about dsdt, i used every single kext for NVidia but nothing works or maybe i am doing something wrong, as the same for the Bluetooth and the sd card reader

how can i release the potential of all my components on my laptop. i use chameleon 2.2 for booting

PLEASE HELP!!!!

Share this post


Link to post
Share on other sites

I am using the steps: Non-booting OS X.

 

Is there a similar way I can perform these beginning steps without having to use Windows? I would rather not waste my time dual booting my Macbook Pro with Windows.

Share this post


Link to post
Share on other sites

I was about to attempt the update, but after reading these posts, I believe I am going to wait for Niresh to release a 10.9.2 patch/installer or something. My installation works perfectly right now, I don't wanna mess it up.

Share this post


Link to post
Share on other sites

I was about to attempt the update, but after reading these posts, I believe I am going to wait for Niresh to release a 10.9.2 patch/installer or something. My installation works perfectly right now, I don't wanna mess it up.

 

My system works so well with niresh 10.9.0 and I'm not too sure to update after reading this problem.

However, any chance to see a new Niresh distribution with 10.9.2 ?

Share this post


Link to post
Share on other sites

@mtx4 Very slim chance of seeing a Niresh Distro just for 10.9.2 especially with 10.9.3 around the corner

Share this post


Link to post
Share on other sites

What about 10.9.0 to 10.9.3?

 

Is there any solution?

 

Thanks,

 

Andrei

Share this post


Link to post
Share on other sites

hi everyone i have 10.9 running on virtual box for testing before i do it on my pc when i tried to do a straight update from 10.9.0 to 10.9.3 the virtial box crashes i have the latest veriosn of it my pc specs is amd phenon 2 r7 240 amd radeon gphic card on a windows 7 ult would this fix up guid work on it also

Share this post


Link to post
Share on other sites

I have a white screen with a spinning cursor and nothing more

I ccan reach the desktop with -x flag (safe mode) only

 

any idea how can I fix this?

Share this post


Link to post
Share on other sites

i got prob of kernel panic after updating to 10.9.4

plz...tell wt to do???

 

Share this post


Link to post
Share on other sites

When I follow the torrent for Niresh 10.9, I get Ubuntu, but the file name is "Mavericks 10.9 ISO .torrent". Do you have another torrent?

Share this post


Link to post
Share on other sites

hola como evito la actualización no me interesa actualizar el problema que cada vez que reinicio me pide la actualización y ya van dos veces que se actualiza sin darme cuenta y de ahí no enciende ya probé el tutorial pero no me funciona por que es en vmware   así que solo quiero saber como evitar la actualización  

Share this post


Link to post
Share on other sites

gracias alguien ya me ayudo con lo de la actualización ya pude ignorarlo y ya no tengo problema  

Share this post


Link to post
Share on other sites

@prajval

use these boot arguments to boot into mac: -v cpus=1 GraphicsEnabler=No dart=0 npci=0x2000

 

then download and run Lapic Kernel Patcher: http://www.hackintos...el-patcher-v07/

 

patch mach_kernel using lapic kernel patcher and restart mac, now run mac without the above boot arguments and you wont have kernel panic now xsmile.png.pagespeed.ic.5Yux4gu5_h.png

Share this post


Link to post
Share on other sites

Hmm...what about 10.9.4? Can I safely update on my AMD machine?

Share this post


Link to post
Share on other sites

Just finished installing 10.9.0 and updated it to 10.9.4

But since then I can only boot in with -v -x or -v -f

Else getting stuck on "Still waiting for root device".

 

Any Ideas?

 

This is the shortest I've ever run a Hackintosh  :D

Needless to say, I won't update it once I get this working.

 

One more thing, every time I reboot (force reboot rather) my system, it looses it BIOS settings. Not sure if these things are all related but any direction would be greatly appreciated.

 

My System:

Dell Optiplex 745 DT

Core2Quad Q6700 2.66 Ghz (OSx takes it as a Xeon)

4 GB DDR2 (for now)

Onboard Graphics (for now)

Share this post


Link to post
Share on other sites

Bump!!!

Share this post


Link to post
Share on other sites

Bump!!!

well the solution is neither getting posted here nor can I open new thread maybe the mod will make the thread active later maybe becoz of the lengthy post its not accepting but its or rather due to my few post maybe I need to increase my post in order to open thread 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community.

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Contribute

    This is a free website, We'll try to keep it that way, Your donations and disabling Adblock makes this site going on, Thanks for understanding.



    $13.17 of $100.00 goal reached.
    Donate Now
  • Download Hackintosh

  • Posts

    • HI i have this card ATI Radeon HD 5770 Series and I have it working, but I got a problem with vram only have 7 mb I need help to solve this because i have problems with some glitches in the display. I haver clover . PD: My graphics card have 2gb      
    • Hi, I am trying to make bootable USB for Hackintosh , I tried TRANSMAC and Win32disk image from my Windows 10 PC, soon after completion USB not accessible. Please advise.   Thank you,  
    • That's happen every time that i am trying to install a hackintosh on my pc i can't find a solution. I tried a lot of different flags.  Pc specs:  GeForceGTX760 4GB Intel i7-4820K MSI Global X79A-GD65 (8D)   There is a video: https://streamable.com/us6nf  
    • nobody can help me
    • I have a GA-H81M-S mobo with G3240 Pentium (R) processor. I am not using the IGP but an Nvidia GT-710 1GB DDR3 dedicated Graphics card. I followed posts in other forums and managed to install once. After upgrade and reboot, I messed with clover configurator and now I can't get to the install screen. I get stuck on VoodooPS2Mouse: Version starting on OS X Darwin 16.4. If this forum is still alive, please help
  • Download Statistics

    • Files
      855
    • Comments
      2,150
    • Reviews
      2,619

    Latest File
    By Niresh

    230    2

×